• WhiteOakBayou@lemmy.world
    link
    fedilink
    English
    arrow-up
    88
    ·
    9 months ago

    If you find yourself making a male-to-male adapter stop. Question all the steps that lead you there. Probably find another way.

    • Dharma Curious@startrek.website
      link
      fedilink
      English
      arrow-up
      12
      ·
      9 months ago

      Used to do property preservation (cleaning out foreclosed homes), and would use a male-male to get power from the generator around the house. I’ve never felt so much fear as when hooking those things up. I was as safe with it as possible, which is, obviously, not safe enough. But my dad now knows that’s possible, and I’ve caught him trying to do similar since, and it scares the shit out of me, because he’s the type that thinks some duct tape around a frayed extension cord is good enough.

      • Darkassassin07@lemmy.ca
        link
        fedilink
        English
        arrow-up
        14
        ·
        9 months ago

        That works great until you accidentally connect one side of the split-phase service with the other side… Your male-to-male cable becomes a short across 240vac.

        Also: if you don’t turn the main breaker off first, you are now back-feeding power into lines the local linemen expect to be dead, potentially electrocuting them… This is why specific receptacles connected with a generator interlock kit (breaker that can only be turned on while the main is off) are used.

  • surewhynotlem@lemmy.world
    link
    fedilink
    English
    arrow-up
    55
    ·
    9 months ago

    Check that the electrical power is off with a meter. Don’t trust that you shut the switch. Some really creative wiring or frayed wires can cause them to be unexpectedly live.

    • bus_factor@lemmy.world
      link
      fedilink
      English
      arrow-up
      30
      ·
      9 months ago

      I heard a story of a guy working on a high voltage, high current piece of equipment. He confirmed that the power was off. Just to be sure, he threw a big wrench at the terminals so they would short if they were still live. His wrench evaporated. Then they actually turned the power off. He lost his wrench, but saved his life.

    • geekworking@lemmy.world
      link
      fedilink
      English
      arrow-up
      12
      arrow-down
      1
      ·
      9 months ago

      Non-contact voltage tester pens are cheap and made for this purpose. Don’t need a meter to measure. Just need to know live or not.

      • Darkassassin07@lemmy.ca
        link
        fedilink
        English
        arrow-up
        15
        ·
        edit-2
        9 months ago

        They’re also notoriously unreliable. Fine for casually looking for powered circuits, but if you’re going to touch the conductors at all, use a meter.

        As an electrician; it’s drilled into your head to use an actual physical-contact meter that you’ve just tested for function on a known good power supply.

        Some courses even demand you re-test the meter after you’ve checked the circuit you’re testing.

      • Raffster@kbin.social
        link
        fedilink
        arrow-up
        1
        ·
        9 months ago

        They are called death sticks for a reason. Always use a known working 2 point meter, and know how to use it correctly. That is the live saving tip here.

    • Lileath@lemmy.blahaj.zone
      link
      fedilink
      English
      arrow-up
      2
      ·
      9 months ago

      And don’t let anyone close to the breaker box while you are working, my grandfather nearly died when some idiot turned the power back on for an industrial machine he was repairing. In his case both the elecrricity and the machine itself could have killed or disabled him.

      • ricecake@sh.itjust.works
        link
        fedilink
        English
        arrow-up
        1
        ·
        9 months ago

        I believe that’s why a lot of machines now have locks, so the person working on it can lock the machine with a padlock and take the key with them.

        Looking around, it seems like some setups now have a lock per person doing the work, so no one can accidentally leave someone in danger.

    • CascadianGiraffe@lemmy.world
      link
      fedilink
      English
      arrow-up
      1
      ·
      9 months ago

      I would say at least 20% of the water heaters I’ve replaced were not wired to the breaker labeled “water heater”. I only had to learn that lesson once.

  • pdxfed@lemmy.world
    link
    fedilink
    English
    arrow-up
    48
    ·
    9 months ago

    Learn CPR for infants and small kids. It’s usually a different or additional class to standard adult and kid CPR that I think goes down to 2 year olds. You don’t want that memory.

    Always wait a second before going if you’re in the front after light turns green. See too many fucking murderous psychos trying to save 20 seconds by roaring through fully red lights that they missed when it turned from yellow.

    Add a water filter with pump to your survival kit. Costs like $20 bucks and means you could drink out of a damn stream in a disaster if mains burst, etc. given the state of poor emergency response and planning that has been on display in the US since Katrina and continues through COVID, NO ONE is planning or going to save you. Water is as important as it gets.

    Insulated foil bags/blankets for your car. If you get suck and have to sleep overnight, if you run out of gas they might mean the difference between keeping toes, legs, fingers or your life. They’re like $5 and smaller than a deck of cards and weigh almost nighting.

    Always have a hatchet in your trunk. It’s a hammer, a cutting tool, weapon, and 500 other things I learned reading The Hatchet as a kid.

    Know how to find north, and read a map.

    Go for your free annual checkups, especially if you’re healthy–keep yourself that way!

    • Frozengyro@lemmy.world
      link
      fedilink
      English
      arrow-up
      14
      ·
      9 months ago

      I would add in addition to waiting a second after the light turns green, look both ways while you’re waiting. Takes almost no time, but saves lives.

      • Lemmygizer@lemmy.world
        link
        fedilink
        English
        arrow-up
        10
        ·
        9 months ago

        Please repeat that to the guy who ignored a stop sign and hit me in a zebra crossing last week.

        Thankfully for me, I was paying attention. I managed to hop on the hood and roll through the impact.

      • mememuseum@lemmy.world
        link
        fedilink
        English
        arrow-up
        9
        ·
        9 months ago

        A few years ago a dump truck slid through an intersection in front of me and the light was green my way. It was going too fast for the road conditions. If I hadn’t looked, it would have t-boned me on the driver’s side.

        • Bizarroland@kbin.social
          link
          fedilink
          arrow-up
          4
          ·
          9 months ago

          I have been tboned by a person who didnt stop at a red light. If I had waited 2 seconds they would have missed me completely.

          I got sent to the hospital, they tried to say I ran the light. Fortunately helpful bystanders corrected her and she was found at fault.

    • Mirshe@lemmy.world
      link
      fedilink
      English
      arrow-up
      1
      ·
      edit-2
      9 months ago

      I agree with the second one. I very nearly wound up compacted into jello after a semi blew through a light and t-boned the driver’s side back end of my work van going a good 50-60 MPH. Now everyone on the road thinks I drive like a grandma, but I’d rather be slow and make everyone behind me upset than be dead.

  • DuckOverload@lemmy.world
    link
    fedilink
    English
    arrow-up
    45
    arrow-down
    3
    ·
    9 months ago

    If you party around people who do hard drugs (festivals, shows, etc), get a narcan inhaler and know how to administer it. It’s very simple, and there are orgs that will give you one for free. Fent is way too common, and there’s other bad shit out there. You could save a life.

  • AlexWIWA@lemmy.ml
    link
    fedilink
    English
    arrow-up
    41
    ·
    edit-2
    9 months ago

    Use jack stands for your car. If your body will be under the car for even a second, there should be jack stands. There were five different people at my high school who were in a wheel chair because they thought the jack was enough.

    I don’t care if your jack costs $100,000 made of pure titanium; do not trust it.

    • netburnr@lemmy.world
      link
      fedilink
      English
      arrow-up
      13
      ·
      edit-2
      9 months ago

      Similar to this, once you have a vehicle on jack stands, shake it lightly to make sure it doesn’t fall easily. Better to find out now by shaking the car before being under it.

      • AlexWIWA@lemmy.ml
        link
        fedilink
        English
        arrow-up
        2
        ·
        9 months ago

        True. It’s okay if your car falls a few inches. At worst you’ll have a blown shock.

    • marmotworks@lemmynsfw.com
      link
      fedilink
      English
      arrow-up
      10
      ·
      9 months ago

      Taking a wheel off of a car, and you don’t have jack stands? You have jack stands and are taking a wheel off as part of your work? Does it involve being under the car? Throw that wheel on the ground under the frame rail / pinch weld. If something horrible happens and the jack kicks, dropping the car on you, it may save your life, and you have to put that wheel somewhere anyway

    • carzian@lemmy.ml
      link
      fedilink
      English
      arrow-up
      8
      ·
      9 months ago

      Related pro tip, if you’re changing a flat tire and don’t have any jack stands, place the spare/damaged wheel under the car while you’re working on it. Better to have the car fall on the wheel then potentially your leg

      • AnarchoSnowPlow@midwest.social
        link
        fedilink
        English
        arrow-up
        1
        ·
        9 months ago

        I do this anytime I take a wheel off, even with jack stands. Doesn’t hurt anything and I’ll take anything extra between the chassis and my head I can get.

      • signor@lemmy.world
        link
        fedilink
        English
        arrow-up
        1
        ·
        9 months ago

        Why would you be under a vehicle to change a flat? You just sitting at the wheel legs under the car?

    • squiblet@kbin.social
      link
      fedilink
      arrow-up
      7
      ·
      9 months ago

      There was a waiter at my second job who was crushed by a car that fell off a Jack. Same, he was in a wheelchair. But then he (probably partially from continuing to do meth) had a heart attack and died 6 months later.

        • squiblet@kbin.social
          link
          fedilink
          arrow-up
          1
          ·
          9 months ago

          We weren’t either. I guess being in a wheelchair is hard on your heart already. He was only 45 too, and a really chill and nice dude.

    • Clay_pidgin@sh.itjust.works
      link
      fedilink
      English
      arrow-up
      1
      ·
      9 months ago

      I lost a coworker when his beloved 70s Camaro fell on him while he was alone at home. His partner had to come home and find him, and he was never quite the same. I tell everyone to use jack stands or a block or a wheel.

  • Gigan@lemmy.world
    link
    fedilink
    English
    arrow-up
    36
    ·
    9 months ago

    If you’re cleaning, don’t mix bleach and vinegar. It produces chlorine gas which can kill you.

  • lettruthout@lemmy.world
    link
    fedilink
    English
    arrow-up
    33
    ·
    9 months ago

    Before getting on a ladder double-check that the feet are placed firmly and (for extension ladders) the angle is not too steep.

    • OhmsLawn@lemmy.world
      link
      fedilink
      English
      arrow-up
      15
      ·
      9 months ago

      Sometimes it’s impractical. After several dangerously deep cuts at work, one of the older guys taught me a fantastic trick, whichever way you have to cut:

      Tuck your elbow tight to your sides when you’re cutting something that you’re holding.

      It limits your range of motion, preventing serious injuries when your knife slips.

      • douglasg14b@lemmy.world
        link
        fedilink
        English
        arrow-up
        6
        ·
        edit-2
        9 months ago

        Wrist action, bottom up, works as well if the thing you’re trying to cut is short and takes a significant amount of tension. If you suddenly pop through unexpectedly you just quickly turn the knife in an arc with your wrist instead of shoving it towards yourself.

        This is an addition to tucking your elbow as you stated.

    • bus_factor@lemmy.world
      link
      fedilink
      English
      arrow-up
      7
      arrow-down
      2
      ·
      9 months ago

      How would failing to do this kill you?

      I prefer to jack the car until the wheel is barely touching, then loosen the nuts while the wheel still doesn’t rotate, then jack it all the way up. Have I been risking my life somehow?

      • ma11en@lemmy.world
        link
        fedilink
        English
        arrow-up
        16
        ·
        9 months ago

        If the nuts are too tight you risk rocking the car off the jack when you undo them.

        The least you’ll do is possibly damage your cars bodywork the worst is to injure yourself.

      • squiblet@kbin.social
        link
        fedilink
        arrow-up
        8
        arrow-down
        1
        ·
        9 months ago

        That’s about the same. I think the concept is to avoid jerking it around while it’s on the jack.

        • Enk1@lemmy.world
          link
          fedilink
          English
          arrow-up
          1
          ·
          9 months ago

          That and it’s difficult to break the lug nuts free if the wheel can rotate. I solve both problems by just using an impact to ugga dugga them off with the car already jacked up.

  • vexikron@lemmy.zip
    link
    fedilink
    English
    arrow-up
    25
    arrow-down
    2
    ·
    edit-2
    9 months ago

    House or apartment, make sure carbon monoxide detectors are installed NEAR GROUND LEVEL.

    So many slumlords do not even give a fuck, and many homeowners think they are just some other kind of smoke detector.

    EDIT: bus_factor has pointed out to me that this is actually a common misperception. CO actually more or less evenly dissipates in a room and does not settle near the floor.

    https://pubmed.ncbi.nlm.nih.gov/21536403/

    Im now going to think about my life choices that lead me to this moment, and more importantly:

    Go out for a breath of fresh air =P

      • vexikron@lemmy.zip
        link
        fedilink
        English
        arrow-up
        5
        ·
        9 months ago

        Were you expecting consumer protections in the only country on earth that allows advertisements for brand new poorly tested drugs of all kinds on all forms of media?

    • Anemia@lemmy.world
      link
      fedilink
      English
      arrow-up
      4
      ·
      9 months ago

      Never even heard of carbon monoxide detectors irl. Is it used with integrated garages or something like that?

      • douglasg14b@lemmy.world
        link
        fedilink
        English
        arrow-up
        4
        ·
        edit-2
        9 months ago

        Where I live they are required by code in any dwelling that has gas appliances or furnaces. On each level of the dwelling.

        Not only that but they are required to be present in the house when selling the house as well.

        This essentially guarantees that all houses will eventually be up to code as the remediation is required before sales can occur.


        Personally I put one in each room. Unfortunately this also comes as an unfortunate expense. Since combination smoke + CO detectors run ~$30 a piece.

        • Anemia@lemmy.world
          link
          fedilink
          English
          arrow-up
          1
          ·
          9 months ago

          Right, you (i assume) americans use gas stoves and heating etc. Honestly i’ve never even seen a gas stove or gas furnace in person.

          The more you know.

      • vexikron@lemmy.zip
        link
        fedilink
        English
        arrow-up
        2
        ·
        9 months ago

        At least where I am from they are common in more urban areas (mandated technically, but as mentioned SLUMLORDS so its not sctually done in practice) as they have more cars and are nearer to restaurants and other stuff that can have a CO leak.

    • Neil@lemmy.ml
      link
      fedilink
      English
      arrow-up
      3
      ·
      9 months ago

      My stepdaughter at 12 years old accidentally bumped into our gas stove and turned on one of the gas burners and then went to bed. Our cat came into the bedroom and started howling at 2AM and woke us up, alerting us to the smell.

      Little dude saved our lives. The whole house was filled with gas.

      • vexikron@lemmy.zip
        link
        fedilink
        English
        arrow-up
        2
        ·
        edit-2
        9 months ago

        Google also links to a dead url, and when you search the NFPA for their most recent Carbon Monoxide Safety Tips it says that you should follow the manufacturers guidelines for the height you should install a CO monitor at.

        That being said: Damn, you are actually correct.

        https://pubmed.ncbi.nlm.nih.gov/21536403/

        My whole life, including when the Fire Department came to school and did a presentation and had us run through the simulated burning trailer, every instruction manual I have ever read for a CO alarm and everyone I have ever talked to about this all insisted CO alarms be installed near ground level.

        How is that possible? Did CO Alarm manufacturers just get it wrong when CO Alarms were becoming more widespread a decade and a half ago and everyone just parrotted what they were saying without checking? I can even remember news segments on CO danger and needing to install the alarms near the ground.

      • Fermion@feddit.nl
        link
        fedilink
        English
        arrow-up
        1
        ·
        edit-2
        9 months ago

        Yeah the density of carbon monoxide is very close to the density of N2 so it stays fairly well mixed unless you have extremely still air. What matters most is having the detector near where you sleep.

  • Hux@lemmy.ml
    link
    fedilink
    English
    arrow-up
    25
    arrow-down
    2
    ·
    9 months ago

    Never go in against a Sicilian when death is on the line.

  • Darkassassin07@lemmy.ca
    link
    fedilink
    English
    arrow-up
    23
    ·
    9 months ago

    Never ever EVER walk under a forklifts raised load (the pallet it’s carrying).

    Things can fall from it, the hydraulics can giveway, the operator may not see you and lower it on you.

    Especially an ‘order picker’ as the operator can not see under them.

    • douglasg14b@lemmy.world
      link
      fedilink
      English
      arrow-up
      9
      ·
      edit-2
      9 months ago

      Really apply this to almost any suspended load. Don’t walk under loads that are mechanically or hydraulically suspended, there are many ways that the load can fall and crush you.

  • seaQueue@lemmy.world
    link
    fedilink
    English
    arrow-up
    22
    ·
    9 months ago

    If you need to put out a small kitchen fire in an emergency and have no other way to do it rip the top off a box of baking soda and use the contents to smother the fire. As the baking soda heats it releases CO2 starving the fire of oxygen, the remaining salt also prevents oxygen from reaching the burning material.

    Even better, always have a fire extinguisher handy in the kitchen - don’t bury it under the sink or in a closet.

    • shalafi@lemmy.world
      link
      fedilink
      English
      arrow-up
      16
      ·
      9 months ago

      Fire extinguishers and baking soda, always have them in the kitchen.

      Life saver on fire extinguishers: Practice. See a post like this? JUMP and run to your extinguisher. Can you find it by reflex?

      Because if shit goes south, you don’t have time to think about it. Just try it a few times when it occurs to you. Like NOW. A time or three will get you in the zone.

      While you’re at it, check the gauge on the side. Look good? OK, there’s a place to pencil in the last time it was checked. Do so. I just did! Thanks OP!

      • Mouselemming@sh.itjust.works
        link
        fedilink
        English
        arrow-up
        4
        ·
        9 months ago

        When it gets old, AFTER you bring home a new one, take the old one outside and practice with it until it’s used up. Educational and fun.

    • w2tpmf@lemmy.world
      link
      fedilink
      English
      arrow-up
      9
      arrow-down
      2
      ·
      9 months ago

      Does no one have lids for their cookware? Just cover it. A cutting board or cookie sheet works good too.

      • tenextrathrills@lemmynsfw.com
        link
        fedilink
        English
        arrow-up
        5
        arrow-down
        11
        ·
        edit-2
        9 months ago

        Does no one

        Why do you respond like a know it all ass? Maybe your advice is valid but you sound like a prick.

        • Iceblade@lemmy.worldM
          link
          fedilink
          English
          arrow-up
          1
          arrow-down
          1
          ·
          9 months ago

          /Please try to be polite and respectful per rule 1, even if you feel another user isn’t.

        • DudeDudenson@lemmings.world
          link
          fedilink
          English
          arrow-up
          0
          arrow-down
          1
          ·
          edit-2
          9 months ago

          Why do you respond like a know it all ass? Maybe your advice is valid but you sound like a prick.

          Why do you respond like a know it all ass? Maybe your advice is valid but you sound like a prick.

  • Scratch@sh.itjust.works
    link
    fedilink
    English
    arrow-up
    20
    ·
    9 months ago

    Cutting down trees of any real size is incredibly dangerous. They can kick or barber chair and instantly kill you.

  • shalafi@lemmy.world
    link
    fedilink
    English
    arrow-up
    24
    arrow-down
    5
    ·
    9 months ago

    Don’t carry a gun unless you put the work into the learning curve. And it’s a steep curve.

    Make safety an unbreakable habit, and that takes practice. Shoot with someone more experienced, let them correct your mistakes, no matter how minor.

    Putting steel on target, especially under stress, takes mad practice. If you haven’t put 1,000 rounds through your personal weapon, leave it at home. How do you trust a gun you haven’t shot 1,000 times?! Hell, 200 rounds is standard “break in” on a new pistol.

    Can you draw it and get on target, shaking yourself shitless? Because if that day comes, you’ll be scared shitless. Have you tried? Try. Run until you can’t breathe, draw and fire. Try. Now do it again.

    You don’t have to go nuts memorizing ballistics charts, but have an idea what you can expect from $round at $range. You’re going to have to watch a fuck-ton of videos, and practice, to get a real-world idea of what you’re carrying and what you can do with it. Adjust accordingly.

    Most people are woefully ignorant of what their state law allows in self-defense. Seen the craziest comments from such people. Hint: The law allows far less than you probably think, even in the reddest of states. Again, fuck ton of videos. Learn, or you might find yourself in a concrete and steel cage.

    One more thought; A pistol is not a magical self-defense talisman. A gun is not a, “Get off me!” or “Leave me alone!”, ward. A concealed gun is for one thing only, killing the person you show it to. If you cannot do that thing, I get you, and I’m with you, but don’t carry.

    Much the same goes for a home defense gun. Learn and train. Or do not. You’re my friend either way.

    (I’ll plug Paul Harrell’s channel. Zero politics, just the facts, stated and demonstrated, mildly amusing. Hundreds of videos on gun related subjects. And some fun presentations outside the gun world!)

      • Iceblade@lemmy.worldM
        link
        fedilink
        English
        arrow-up
        9
        ·
        9 months ago

        There is definitely a time and place for firearms, though most folks in the developed world have neither reason nor knowledge to do that.

        My cousins for instance - they’ve a farm in southern Sweden, and have hunting rifles. Mostly for hunting, protecting cattle and crops (wild boar can tear up a field in a jiffy). However, I don’t doubt they’d use them for protection if it came to that. The travel time for cops if they called 112 (our 911) would be in excess of an hour.

      • Lileath@lemmy.blahaj.zone
        link
        fedilink
        English
        arrow-up
        5
        arrow-down
        1
        ·
        9 months ago

        Vulnerable people should be able to defend themselves. GSRM have a high rate of being assaulted and weapons can be a strong deterrent to that, although it probably would be a better idea to carry pepper spray and other nonlethal weapons provided you know how to use them.

    • Neil@lemmy.ml
      link
      fedilink
      English
      arrow-up
      2
      ·
      9 months ago

      One big thing that i learned while training for my CCW was even if you are in the right and shoot someone, your life is about to be hell. The average self defense shooting will run around 500K or something like that. It’s just a life ruining event no matter what.

    • PsychedSy@sh.itjust.works
      link
      fedilink
      English
      arrow-up
      0
      arrow-down
      1
      ·
      9 months ago

      Group shooting with rednecks will get you well on your way on the basics. It’s like having a shitload of uncles all excited to have you sharing a hobby. You’ll get to fire a lot of different firearms, too.

        • PsychedSy@sh.itjust.works
          link
          fedilink
          English
          arrow-up
          1
          ·
          9 months ago

          You’re insane. I’ve gone shooting with them and they’re spectacular about safety. Once they know you’re a noob they’re all there to tell you how to shoot.